立式接鏈環為目前比較常用的一種礦用鏈條用接鏈環，主要由兩個半環和彈銷組成。兩半環分別連接鏈條兩端的第二鏈環、第三鏈環，鎖緊后嵌入彈性彈銷，使其結合牢固，避免脫鏈。有的接鏈環中間設計有連接部分，有的中間空開，由其安裝方法與連接齒形（鋸齒、弧齒、卡塊）決定。

　　當使用不當在刮板機機頭下方造成堆鏈時易出現問題，此時接鏈環A點受到摩擦力F和刮板機底板的壓力N作用。而f=μ*N，μ為摩擦系數。N由diyi鏈環、dier鏈環、disan鏈環向下的部分重力、接鏈環的自身重力和左端其他鏈條對接鏈環向下的拉力分量組成。在這種情況下，如果要拉開鏈條，將接鏈環逆時針轉動至水平方向。拉力F1越大，N越大，從而摩擦力f越大。而且接鏈環越長，α角越小，越不容易拉開。所以在拉開鏈環的過程中，由于在寬度方向失效需要施加的力要遠小于長度方向需要施加的力，接鏈環易從寬度方向脫鏈。接鏈環為易損件，正常情況下，接鏈環的脫鏈方向為長度方向。